Tool Hire

0345 604 5337

Combination Hire Pack - 240V Floor Sander & Edging Sander

Floor Sander Combi Pack
Floor Sander Combi Pack
Floor Sander Hire
Edging Sander Hire
Floor Sander And Sheets
Edging Sander And Sheets
Edging Sander Rental
Everyday Product Hire Guarantee

Save money and time by hiring a 240V floor sander and 240V edging sander together.

Supplied with RCD unit.

Floor Sander Additional Information:

The floor sander is used for sanding many types of wooden floors including garden decking and will remove paint, stains and varnishes from a wooden floor leaving a smooth finish. A four brush motor powers a sanding drum that is dynamically balanced and is covered in a unique drum rubber. A major advantage is that the unit is completely self-contained with the added quality of a high-dust-pickup-efficiency. For easy transport and storage the sander breaks apart into three simple sections. With a low voltage trip switch the floor sander is ideal for both home and professional use.

  • Based On: Hiretech HT8 Drum Floor Sander
  • Off Load Current 240V: 5A
  • Off Load Current 110V: 8A
  • Average Load Current 240V: 8A
  • Average Load Current 110V: 15A
  • Noise: 95 dBA at 1M
  • Vibration: 1.60 m/s² rms
  • Motor RPM: 8,500
  • Drum RPM: 3,300
  • Dimensions W x D x H: 322mm x 940mm x 855mm
  • Weight Net: 41.5kg
  • Sanding Sheet Width: 200mm

Edging Sander Additional Information:

The edging sander takes over where the floor sander finishes and allows for sanding right up to the skirting board. Giving unrivalled balance and feel, features include a powerful four brush motor that drives a dynamically balanced metal backed sanding pad, wheel castors that allow easy change of direction and a high powered vacuum system.

  • Based On: Hiretech HT7 Disc Floor Sander
  • Off Load Current 240V: 5A
  • Off Load Current 110V: 8A
  • Average Load Current 240V: 8A
  • Average Load Current 110V: 15A
  • Noise: 100 dBA at 1M
  • Vibration: 2.71 m/s² rms
  • Motor RPM: 13,000
  • Disc RPM: 3,300
  • Dimensions W x D x H: 276mm x 505mm x 325mm
  • Weight Net: 16.4kg
  • Sanding Disc Diameter: 178mm

Sanding Tips:

Before sanding, empty the room completely of furniture and remove any old floor coverings, nails and anything else that is attached to the floor, then vacuum and clean the room thoroughly. Basically, you want an empty clean surface to start working on.

Inspect the floor closely, drive in all nail heads and remove any carpet staples or fasteners from former flooring to avoid tearing the sanding sheets.

The direction of sanding often depends on the floor's condition. If it is fairly flat, it may be possible simply to use the sander up and down the floor boards' grain. If the floor is uneven, or has a very thick coating of paint or varnish, go across the grain. Sanding at a right angle to boards may damage them, so sand at about 45 degrees. Cross the room in one direction, then the other before finishing along the grain. Reduce the coarseness of the sandpaper you use as you progress, finishing with the finest grade.

If your floor needs a lot of sanding, start with the coarse (P40 Grit) sanding sheets, for a floor in a better condition, the medium (P80 Grit) sanding sheets are better.

Make sure the drum of the sander is sitting off the floor before starting the machine and then lower the drum onto the floor slowly and move at a gradual, even pace to ensure the sander creates an even finish. Before the end of each run ensure you raise the drum of the sander off the floor before changing direction or switching the machine off.

Use the edging sander to get closer to the skirting boards where the floor sander can't reach. Because these sanders use a disc that sands across the grain, you might need to use a finer grit paper than the one you used with the floor sander.

Sanding a floor always produces a lot of dust (even though the machines have dust bags), so always wear goggles and a face mask to avoid inhaling the dust, ventilate the room by opening windows and seal around the door (to prevent the dust from getting into the rest of the house). Sanders are also noisy, so ear protection should also be worn.

Do not let the dust bag fill more than halfway before changing, otherwise the additional weight of the dust bag negatively affects the sanding of the floor.

This combination pack does not come complete with sanding sheets, discs or dust bags, please remember to add these when placing your order.

It is advisable to order at least 3 of each grit of sanding sheets and discs per room and at least 2 dust bags per room (unused sheets, discs and bags can be returned and monies refunded).


Everyday Hire Guarantee Product 240V Item Breathing Mask Required Eye Protection Required Hand Protection Required Item Can Be Transported By Estate Car Available For Collection From Branch Available To Order Online Order By Phone 0345 604 5337
Code WEB74
Item Combination Hire Pack - 240V Floor Sander & Edging Sander
Same Day £41.99
+ Day £14.00
Weekend £55.99
Weekly £69.99

Useful Information

Near Me
Order and Collect
Branch Opening Times
Payment Methods
About Us

Awards & Accreditation