Floor Sander & Edging Sander Combination Pack - 240V

Sander combi pack
Sander combi pack
Electric Floor Sander
Floor Edging Sander
Floor Sander Sanding Sheet
Edging Sander Sanding Disc
Floor sander dust bag
Floor eding sander dust bag

Save money and time by hiring the Floor Sander and Edging Sander together.

The floor sander is used for sanding many types of wooden floors including garden decking and will remove paint, stains and varnishes from a wooden floor leaving a smooth finish.

The edging sander takes over where the floor sander finishes and allows for sanding right up to the skirting board.

This combination pack does not come complete with sanding sheets or discs. When adding sanding sheets and discs to your order it is advisable to order at least 5 of each grit per room, as unused sheets and discs can be returned and monies refunded. Extra dust bags are also available to buy.

Additional Information:

The floor sander: A four brush motor powers a sanding drum that is dynamically balanced and is covered in an unique drum rubber. A major advantage is that the unit is completely self-contained with the added quality of a high-dust-pickup-efficiency. For easy transport and storage the sander breaks apart into three simple sections. With a low voltage trip switch the floor sander is ideal for both home and professional use.

The edging sander: Gives unrivalled balance and feel. Features include a powerful four brush motor that drives a dynamically balanced metal backed sanding pad, wheel castors that allow easy change of direction and a high powered vacuum system.

1 x Floor Sander Dust Bag and 1 x Edge Sander Dust Bag are supplied with the sanders, 1 x RCD Power Breaker is also supplied.


Sanding Tips:

Before sanding, empty the room completely of furniture and remove any old floor coverings, nails and anything else that is attached to the floor, then vacuum and clean the room thoroughly. Basically, you want an empty clean surface to start working on.

Inspect the floor closely, drive in all nail heads and remove any carpet staples or fasteners from former flooring to avoid tearing the sanding sheets.

The direction of sanding often depends on the floor's condition. If it is fairly flat, it may be possible simply to use the sander up and down the floor boards' grain. If the floor is uneven, or has a very thick coating of paint or varnish, go across the grain. Sanding at a right angle to boards may damage them, so sand at about 45 degrees. Cross the room in one direction, then the other before finishing along the grain. Reduce the coarseness of the sandpaper you use as you progress, finishing with the finest grade.

If your floor needs a lot of sanding, start with the coarse (P40 Grit) sanding sheets, for a floor in a better condition, the medium (P80 Grit) sanding sheets are better.

Make sure the drum of the sander is sitting off the floor before starting the machine and then lower the drum onto the floor slowly and move at a gradual, even pace to ensure the sander creates an even finish. Before the end of each run ensure you raise the drum of the sander off the floor before changing direction or switching the machine off.

Use the edging sander to get closer to the skirting boards where the floor sander can't reach. Because these sanders use a disc that sands across the grain, you might need to use a finer grit paper than the one you used with the floor sander.

Sanding a floor always produces a lot of dust (even though the machines have dust bags), so always wear goggles and a face mask to avoid inhaling the dust, ventilate the room by opening windows and seal around the door (to prevent the dust from getting into the rest of the house). Sanders are also noisy, so ear protection should also be worn.

Do not let the dust bag fill more than halfway before changing, otherwise the additional weight of the dust bag negatively affects the sanding of the floor.


Technical Information:

  • Based On: Hiretech HT8 Drum Floor Sander
  • Off Load Current 240V: 5A
  • Off Load Current 110V: 8A
  • Average Load Current 240V: 8A
  • Average Load Current 110V: 15A
  • Noise: 95 dBA at 1M
  • Vibration: 1.60 m/s² rms
  • Motor RPM: 8,500
  • Drum RPM: 3,300
  • Dimensions W x D x H: 322mm x 940mm x 855mm
  • Weight Net: 41.5kg
  • Sanding Sheet Width: 200mm
  • Based On: Hiretech HT7 Disc Floor Sander
  • Off Load Current 240V: 5A
  • Off Load Current 110V: 8A
  • Average Load Current 240V: 8A
  • Average Load Current 110V: 15A
  • Noise: 100 dBA at 1M
  • Vibration: 2.71 m/s² rms
  • Motor RPM: 13,000
  • Disc RPM: 3,300
  • Dimensions W x D x H: 276mm x 505mm x 325mm
  • Weight Net: 16.4kg
  • Sanding Disc Diameter: 178mm

Everyday Hire Guarantee Product 240V Item  LOW Vibration Rated Item RCD Power Breaker Required Hearing Protection Required Breathing Mask 1 Required Eye Protection Required Hand Protection Required Accessories Available For This Item Item Can Be Transported By Estate Car Available For Collection From Branch Available To Hire Online Order By Phone 0370 99 00 999
Code 220140
Item Floor Sander & Edging Sander Combination Pack - 240V
Same Day £52.65
+ Day £16.09
Weekend £68.54
Weekly £84.43

Useful Information

Branch locations
Aberdeen
Ashford
Barnsley
Bradford
Birmingham
Brighton
Bristol
Canning Town
Cannock
Canterbury
Cardiff
Carlisle
Chessington
Chesterfield
Colchester
Coventry
Croydon
Dartford
Derby
Edinburgh
Exeter
Folkestone
Gateshead
Gillingham
Glasgow
Greenford
Heathrow
Hull
Leeds
Leicester
Liverpool
Long Eaton
Loughborough
Maidstone
Manchester
Mansfield
Margate
Melton Mowbray
Middlesbrough
Newcastle
Northfleet
Norwich
Nottingham
Peterborough
Plymouth
Sheffield
Shrewsbury
Sittingbourne
Skipton
Southampton
Stevenage
Stoke
Strood
Swansea
Telford
Tonbridge
Tower Bridge
Warrington
Aberdeen
Ashford
Barnsley
Bradford
Birmingham
Brighton
Bristol
Canning Town
Cannock
Canterbury
Cardiff
Carlisle
Chessington
Chesterfield
Colchester
Coventry
Croydon
Dartford
Derby
Edinburgh
Exeter
Folkestone
Gateshead
Gillingham
Glasgow
Greenford
Heathrow
Huddersfield
Hull
Leeds
Leicester
Liverpool
Long Eaton
Loughborough
Maidstone
Manchester
Mansfield
Margate
Melton Mowbray
Middlesbrough
Newcastle
Northfleet
Norwich
Nottingham
Peterborough
Plymouth
Sheffield
Shrewsbury
Sittingbourne
Skipton
Southampton
Stevenage
Stoke
Strood
Swansea
Telford
Tonbridge
Tower Bridge
Warrington
Order and Collect

Order & Collect

Please note

Our order and collect service is available on all orders placed online, on the phone or in the local branch. However, you may not get the same special offers and prices as advertised on this site.

Our branch staff will show you how to use the machine in the branch, but please also note the hirer should collect so he / she knows how to use the equipment.  If you are collecting from us on behalf of someone else, please be aware we cannot be held responsible for any operating errors or faults.

When collecting from a local Hire Station branch please make sure you take two forms of ID and one must be photographic.  Hire Station may also require a deposit when you collect, so please ensure you take a credit card. Deposits will of course be returned when you return the item back to the branch.

You can return the equipment you hire to ANY Hire Station branch.

Awards & Accreditation